Deep Well water level sensor is to apply Hydrostatic Level Sensor to deep well. Well water level sensor submerged in deep well work together with submersible water pump. Range within 300m ～ 1000m.

Features of Deep Well Water Level Sensor:

Specifications of Deep Well Water Level Sensor

Range	Various ranges within 300m ～ 1000m
Medium temperature	－20 ℃ ～ 70 ℃
Ambient temperature	－10 ℃ ～ 60 ℃
Supply voltage	DC 24V (12V ～ 32V)
Load characteristics	Current output type≤500Ω; Voltage output type: ≥3KΩ
Insulation resistance	＞ 100MΩ
level of accuracy	Class A: 0.2 Class B: 0.5 Class
Non-linear	± 0.2% F.S
Hysteresis and reproducibility	± 0.1% F.S
Long-term stability	± 0.1% F.S / y
Thermal zero drift	± 0.03 ％ F.S / ℃
Response time	≤50ms
Maximum working pressure	2 times the range
Electrical connections	Stainless steel cable connection
Material of external parts	Stainless steel / 316 stainless steel
Shell material	Stainless steel / 316 stainless steel
Measuring medium	Oil, water and other media compatible with 316 stainless steel
Protection level	IP68

Extended Reading: 3 inch (3″) Water Flow Meter

Applications of Deep Well Water Level Sensor

• Suitable for deep water level measurement of deep wells and groundwater;
• Pumping stations, reservoirs, water channels and other water supply and sewage projects;
• The pressure and oil level of the gas field in the oil field;
• Ships and marine equipment;
• Groundwater resource management;

Extended reading: Capacitive water level sensor

Submersible pressure transmitter for level measurement

By videos below, you can know more about submersible pressure transmitter for level measurement：

Video source: https://www.youtube.com/embed/EMotg3BQjlI?rel=0

How this Water Level Sensor Works

Well Water Level Sensor is one type of Hydrostatic Level Sensor.

The basic working principle of Hydrostatic Level Sensor is static pressure level measurement.

In liquid, the pressure generated at a certain depth is generated by the weight of the medium itself above the measurement point. It is proportional to the density of the medium and the local acceleration of gravity.

The formula P = ρgh reflects the proportional relationship between them.

Where P = pressure, ρ = medium density, g = gravity acceleration, h = depth of measurement point.

Therefore, the physical quantity measured by the input liquid level gauge is actually pressure. It can be understood by the calibration unit mH2O of the input level gauge. The actual liquid level must be obtained by conversion after knowing the two parameters of density and gravity acceleration. In the industrial field, such conversion is usually performed by a secondary instrument or PLC.

The Hydrostatic Level Sensor mainly measures corrosive liquids such as hydrochloric acid, hydrogen peroxide, etc. Or chemical and electroplating wastewater. Mainly used in measuring corrosive media. It has the advantages of strong corrosion resistance and stable performance.

Extended Reading: LORA water meter

Deep Well Water Level Sensor Installation:

Well Water Level Sensor and oil pipe (water pipe) go down to install together:

1. The deep well liquid level transmitter should use the special ferrule fixing cable for the matching oil pipe (water pipe). Prevent crushing and damaging the cable. The sensor part should be installed vertically to prevent the sediment and other impurities from burying or blocking the transmitter probe part.
2. The three-way outlet part is filled with special sealant pad and sealant. Use a wrench to tighten the compression nut. Prevent air leakage.
3. The entire signal line leads to the interior of the power distribution cabinet. Prevent rainwater at the terminal from penetrating into the cable to cause damage. The transmitter is used for the installation of hydrology, seismic monitoring wells and reservoir dams.
4. When the transmitter is used alone for downhole measurement. When the cable length is greater than 100 meters, an additional load-bearing wire rope should be added. Go down with the signal cable together. Protect the signal cable to prevent the signal cable from being damaged due to excessive force.

Extended reading: Magnetic water meter-ultrasonic water meter-mechanical water meter

Well Water Level Sensor calibration method:

Unscrew the protective cover. You can see the zero and full range resistors. External standard power supply and ammeter (above 0.2 pole). To adjust. Proceed as follows:

◆ In the case of no liquid in the transmitter. Adjust the zero resistor. Make it output current 4mA.
◆ Transmitter is filled to full scale. Adjust the full-scale resistor. Make the output current 20mA,
◆ Repeat the above steps two or three times. Until the signal is normal.
◆ The adjustment is completed. Tighten the protective cover.

Extended Reading: What is level transmitter working principle?

Precautions for using Well Water Level Sensor:

1. When the static pressure input type liquid level gauge is installed. The pressure tube must be inserted vertically into the measured medium;
2. For media with impurities or crystals. The head of the gas collector must be cleaned regularly. To prevent clogging;

Read more about: Why Is The Submersible Level Transducer The First Choice For Water Level Measurement?

FAQ

Deep Wells Water level sensor is designed for deep well level measurement. It effectively solves the problem of deep well liquid level measurement difficulty. Sino-Inst offers over 50 water level sensors. About 50% of these are Submersible level Transmitter, 40% are water meters, and 40% are level meters.
A wide variety of water level sensors options are available to you, such as free samples, paid samples. 
Sino-Inst is a globally recognized supplier and manufacturer of Submersible Pressure Transmitter , located in China. The top supplying country is China (Mainland). You can ensure product safety by selecting from certified suppliers, with ISO9001, ISO14001 certification.

Request a Quote